Design of a Separable Probe for Combustible Gas Detection
-
摘要: 为了解决高空作业安全隐患,提出一种将报警器探头分离的思路,将报警器探头分为两部分,一部分为固定部分,一部分为可移动部分。固定部分包括防爆接线盒及线盒内电磁铁、接线柱等;可移动部分为探头主体,可对其标定、调整等操作。两部分通过电磁铁吸合,在检定或维护保养报警器时,通过遥控器切断电磁铁吸力可方便将探头从高空取下。此外,就防爆接线盒的防爆类型、结构尺寸、结构强度及电磁铁选型等进行详细计算设计。Abstract: This paper proposes a separable probe for combustible gas detection in order to decrease the risk of high-altitude operation.In this design, the probe is divided into two parts, i.e. one fixed part and one removable part. The fixed part includes an explosion-proof junction box and an electromagnet terminal in the box. The removable part is the main part of the probe, which can be removed for calibration and adjustment. The two parts are attached to one another by the electromagnet. When the probe needs verification or maintenance, the electromagnet is turned off by remote control, so that the removable part can be taken off. The explosion-proof type, structure size, structure strength of the explosion-proof junction box, and electromagnet selection are analyzed in detail.
-
Key words:
- alarm probe /
- separable /
- explosion-proof junction box /
- electromagnet /
- combustiblegas
-
表 1 常见可燃气体爆炸性分级分组表
Table 1. Explosive classification and grouping of common combustible gases
气体 级别 组别 引燃温度/℃ 爆炸下限/LEL 甲烷 ⅡA T1 537 5.00% 氢气 ⅡC T1 500 4.00% 表 2 ⅡC类外壳接合面最小宽度和最大间隙
Table 2. Minimum width and maximum clearance for joint surface of Class II C housing
接合面
类型接合面
最小宽
度L/mm最大间隙i/mm V≤100 mL 100 mL<V
≤500 mL500 mL<V
≤2000 mLV>2000 mL 平面接
合面6 0.10 — — — 9.5 0.10 0.10 — — 15.8 0.10 0.10 0.04 — 25 0.10 0.10 0.04 0.04 表 3 应力系数表
Table 3. Stress coefficients
a/b 1.0 1.1 1.2 1.3 1.4 1.5 ∞ $ {C}_{4} $ 0.1374 0.1602 0.1812 0.1968 0.2100 0.2208 0.2208 -
[1] 郭波, 张征, 许思思. 有毒有害气体报警器智能检定装置的研制[J]. 中国测试, 2015, 41(5): 75-78. doi: 10.11857/j.issn.1674-5124.2015.05.019 [2] 徐金生. 可燃气体检测报警器的应用[J]. 计量技术, 2000(8): 44-45. [3] 陈连生. 可燃气体探测器及其设置安装要领[J]. 石油工程建设, 1996(1): 23-25. [4] 李拥军. 一氧化碳报警器检定中常见故障分析[J]. 计量技术, 2005(9): 42-43. [5] 中华人民共和国住房和城乡建设部. 爆炸危险环境电力装置设计规范: GB 50058-2014 [S]. 北京: 中国计划出版社, 2014. [6] 国家质量监督检验检疫总局. 爆炸环境·第二部分 由隔爆外壳“d”保护的设备: GB 3836.2-2010 [S]. 北京, 2010. [7] 臧甲磊, 周严. LNG罐箱仪表监测电路防爆盒设计优化[J]. 研究与开发, 2019, 38(1): 57-61. [8] 张丽晓. 隔爆型电气设备外壳强度及刚度的设计与计算[J]. 电气防爆, 1998(4): 6. [9] 孙海林. 隔爆电气设备外壳强度分析及参数化设计[D]. 西安: 西安理工大学, 2006. [10] 张湄, 张海鸥. ⅡC级隔爆型防爆接线盒的防爆结构设计[J]. 电器设计, 2016(3): 17-21. [11] 邱佳明, 丁汉绅, 王淑娟. 电磁超声钢板测厚装置中脉冲电磁铁的设计[J]. 中国测试, 2018, 44(5): 77-82. doi: 10.11857/j.issn.1674-5124.2018.05.015