Study on the Realization of the Horizontal Position of Metal Gauge and Related Issues
-
摘要: 标准金属量器水准器偏离应有的检定位置或因人为因素未进行水平调整,易导致量器使用状态与应有状态之间发生倾斜,计量颈、液位管中液位与应有位置出现偏差。为定量确定这种偏差带来的影响,通过分析计量颈与液位管的空间几何关系,确定了倾斜导致的量器液位测量偏差的函数关系。对常见液位补偿式金属量器原理进行分析,给出了几种不同形式液位补偿的函数关系式,在此基础上,提出了选择液位管呈垂直排列的液位补偿式量器的建议。对生产过程中产生的计量颈、液位管、标尺与主体部分之间的倾斜进行分析,得出安装倾斜对测量结果无影响。Abstract: If the standard metal gauge level deviates from the due verification position or is not adjusted due to human factors, it will easily lead to the slant between the working state and the due state of the gauge. To determine the impact of such deviation, the spatial geometric relationship between the measuring neck and the level tube is analyzed to determine the function of the deviation of the level measurement caused by the slant. The principle of common level-compensated metal gauges is analyzed, and the functional relationship between several different forms of level compensation is given. On this basis, recommendations are made for selecting level-compensated gauges with vertically aligned level tubes. The slant between the measuring neck, level tube, scale and the main part generated in the production process is analyzed, and it is concluded that the installation tilt has no effect on the measurement results.
-
Key words:
- metal gauge /
- measuring neck /
- level tube /
- ruler /
- realization
-
表 1 标尺与液位管和计量颈之间的测量数据
Table 1. Measurement data between ruler and liquid level tube and measuring neck
/mm 基本信息 标准量器编号 0468 0470 0469 0471 备注 测量项目 1000L(双标尺) 500L(双标尺) 200L 50L 液位管长度(不含安装座) 339.0 339.0 348.0 352.0 253.0 220.0 标尺与液位管
之间的平行性标尺在安装平面
内的测量数据①标尺上下端与液位管距离偏差 0.56 0.40 0.06 0.60 0.40 1.10 ②上下测量点距离(液位管长度) 339.0 339.0 348.0 352.0 253.0 220.0 ③平行性偏差(mm/m) 1.65 1.18 0.17 1.70 1.58 5.00 =1000×①/② 标尺在垂直于安装
平面的测量数据④标尺上下端与安装平面的偏差 0.432 2.775 2.129 1.141 1.239 1.274 ⑤上下测量点的垂直距离 281 269 290 277 192 156 ⑥平行性偏差(mm/m) 1.54 10.32 7.34 4.12 6.45 8.17 =1000×④/⑤ 标尺与计量颈
之间的平行性标尺在安装平面
内的测量数据(1)标尺上下端与计量颈距离偏差 3.66 1.16 0.12 0.16 0.52 1.24 (2)上下测量点的垂直距离 339 339.0 348.0 352.0 253.0 220.0 (3)平行性偏差(mm/m) 10.79 3.42 0.34 0.45 2.06 5.64 =1000×⑴/⑵ 标尺在垂直于安装
平面的测量数据(4)标尺与安装平面的平行性偏差 4.072 0.029 2.783 0.848 1.129 0.622 (5)上下测量点的垂直距离 280 282 264 254 211 181 (6)平行性偏差(mm/m) 14.54 0.10 10.54 3.34 5.35 3.44 =1000×⑷/⑸ -
[1] 国家质量监督检验检疫总局. 标准金属量器计量检定规程: JJG 259-2005 [S]. 北京: 中国标准出版社, 2005. [2] 廉育英, 刘子勇, 张世文, 等. 国家一等标准金属量器组标准装置的建立[J]. 计量学报, 1993(4): 87-93. [3] 戴金桥, 张志清. 标准金属量器检定中应注意的问题[J]. 中国计量, 2013(3): 117-118. doi: 10.3969/j.issn.1006-9364.2013.03.045 [4] 刘晓伟, 赵翠莲, 汪地, 等. 基于面阵CCD的标准金属量器液位监测系统[J]. 计算机测量与控制, 2006, 14(7): 1138-1140. [5] 杨经荣, 车建军, 刘子勇, 等. 一种机械式自动调平的标准金属量器[J]. 中国计量, 2020(2): 94-95. doi: 10.16569/j.cnki.cn11-3720/t.2020.02.028 [6] 车建军, 刘子勇, 杨经荣, 等. 机械式自动调水平的标准金属量器: 201920297598.3 [P]. 2019-10-1. [7] 张英, 万丽芬, 熊骞, 等. 标准金属量器液位测量结构问题的探讨[J]. 中国计量, 2020(7): 119-120. doi: 10.16569/j.cnki.cn11-3720/t.2020.07.044 [8] 郭立功, 贾志宁, 佟林, 等. 高精度液位计自动检测系统研制[J]. 计量科学与技术, 2021(2): 34-38. [9] 张璋, 邵欣铭. 计量颈倾斜对标准金属量器计量的影响分析[J]. 科技展望, 2016(19): 138,160. [10] 曾庆威, 谢清群, 邓玉湖, 等. 标准金属量器不水平引入的液位偏差补偿方法研究[J]. 中国计量, 2017(1): 80-82. doi: 10.16569/j.cnki.cn11-3720/t.2017.01.027 [11] 刘小刚. 标准金属量器液面高度的测量方法[J]. 质量技术监督研究, 2017(3): 8-12. doi: 10.15902/j.cnki.zljsjdyj.2017.03.003 [12] 张英, 郭立功, 万丽芬, 等. 一种精确测量液位管中液位高度的液位计: 201922289856.6 [P]. 2020-11-10. [13] 张英, 杨瑞东, 阳光磊, 等. 一种悬垂式自安平标准金属量器: 202120528839.8 [P]. 2021-09-10. [14] 张英, 郭立功, 万丽芬, 等. 一种筒形游标液位读数装置[J]. 中国计量, 2021(6): 85-86. doi: 10.16569/j.cnki.cn11-3720/t.2021.06.034 [15] 吴安平. 一等标准玻璃量器检定数据处理自动化系统的设计与应用[J]. 计量技术, 2019(8): 43-45.