Design Study on the Measurability of Low-Frequency Standard Shaker

LV Qi; WANG Junbo; ZHANG Ying; LIU Zhihua; XIA Yan; CAI Chenguang

doi:10.12338/j.issn.2096-9015.2021.0675

Volume 66 Issue 4

Jun. 2022

Turn off MathJax

Article Contents

Article Navigation > Metrology Science and Technology > 2022 > 66(4): 101-107, 88

LV Qi, WANG Junbo, ZHANG Ying, LIU Zhihua, XIA Yan, CAI Chenguang. Design Study on the Measurability of Low-Frequency Standard Shaker[J]. Metrology Science and Technology, 2022, 66(4): 101-107, 88. doi: 10.12338/j.issn.2096-9015.2021.0675

Citation:

LV Qi, WANG Junbo, ZHANG Ying, LIU Zhihua, XIA Yan, CAI Chenguang. Design Study on the Measurability of Low-Frequency Standard Shaker[J]. Metrology Science and Technology, 2022, 66(4): 101-107, 88. doi: 10.12338/j.issn.2096-9015.2021.0675

Citation:

PDF( 1303 KB)

Design Study on the Measurability of Low-Frequency Standard Shaker

doi: 10.12338/j.issn.2096-9015.2021.0675

1.
National Institute of Metrology, Beijing 100029, China
2.
China Jiliang University, Hangzhou 310018, China
3.
Beijing University of Aeronautics and Astronautics, Beijing 100191, China

Accepted Date: 2022-04-08

Available Online: 2022-04-22

Publish Date: 2022-06-02

Abstract

Abstract

The low-frequency standard shaker is the main component of the low-frequency vibration standard device, and its measurement performance directly affects the measurement uncertainty of low-frequency vibration calibration. By carrying out the design and research on the measurability of the low-frequency standard shaker, the ability of the metrology guarantee can be improved. Based on the functional analysis of low-frequency standard shakers, this paper analyzes three typical measurement scenarios of low-frequency standard shakers, including type test, conventional use, and periodic measurement, and composes and extracts three key measurement parameters and relevant requirements as the measurable requirements, including transverse vibration ratio, acceleration harmonic distortion, and frequency indication error, and then carries out the measurable design and verification. Given the large distortion of the low-frequency accelerometer in low-frequency calibration, a grating-based measurement method is proposed. The measurement interface and method of the grating are designed by using the measurable design method, which effectively improves the convenience and accuracy of distortion measurement. The measurability design method and the process can provide a reference for the measurability design of other verification and calibration devices.
- low-frequency standard shaker,
- distortion,
- grating,
- measurability design,
- sensor calibration.

FullText(HTML)

References(18)

References

[1]	严普强, 乔陶鹏. 工程中的低频振动测量与其传感器[J]. 振动、测试与诊断, 2002, 22(4): 247-253. doi: 10.3969/j.issn.1004-6801.2002.04.001
[2]	董雪明, 何懿才, 关伟. 加速度计校准技术综述[J]. 计测技术, 2014(4): 5-9.
[3]	Liu Z , Cai C , Lv Q, et al. Improved Control of Linear Motors for Broadband Transducer Calibration[J]. IEEE Transactions on Instrumentation and Measurement, 2021, 70: 1004910.
[4]	李靖, 张峰, 孟春雷, 等 [J]. 对装备可计量性的思考国防科技, 2020, 41(1): 21-23.
[5]	蒋薇. 装备可计量性的相关性模型研究 [D]. 长沙: 国防科学技术大学, 2012.
[6]	黄传跃. 重型直升机发展与应用 [M]. 北京: 航空工业出版社, 2017.
[7]	文裕武, 温清澄. 现代直升机应用及发展 [M]. 北京: 航空工业出版社, 2000.
[8]	徐卫国, 刘天坤, 侯健, 等. 直升机专用检测设备计量保障[J]. 国防科技, 2020, 41(1): 17-20.
[9]	王胜超, 樊哲, 欧佳. 融入军用飞机研制设计流程的计量保证技术研究[J]. 计量与测试技术, 2020, 47(2): 38-42.
[10]	李艳红. 专用测试设备计量管理的问题及对策[J]. 质量与可靠性, 2012, 15(1): 56-59.
[11]	董锁利. 论装备可计量性设计专业化的必然性[J]. 计量信息化与管理, 2013, 33(1): 38-40.
[12]	王朝, 蔡晨光, 杨明, 等. 基于激光干涉仪数字信号解码的振动校准方法[J]. 计量学报, 2021, 42(3): 282-286. doi: 10.3969/j.issn.1000-1158.2021.03.04
[13]	杨明, 蔡晨光, 刘志华, 等. 基于外差激光干涉法的三轴向振动绝对校准方法研究[J]. 计量学报, 2018, 39(2): 201-206. doi: 10.3969/j.issn.1000-1158.2018.02.13
[14]	叶文, 蔡晨光, 杨平, 等. 惯性技术计量领域若干问题的思考与展望[J]. 计量科学与技术, 2021, 65(3): 9-14,52.
[15]	肖宇行, 左爱斌, 杨琪琪. 激光测振位置对加速度计校准结果影响研究[J]. 计量科学与技术, 2020(10): 26-31. doi: 10.3969/j.issn.2096-9015.2020.10.08
[16]	杨明. 基于机器视觉的低频振动校准关键技术研究 [D]. 北京: 北京化工大学, 2020.
[17]	Yang Ming, Cai Chenguang, Liu Zhihua, et al. Monocular vision-based calibration method for determining the frequency characteristics of low-frequency accelerometer[J]. IEEE Sensors Journal, 2021, 21(4): 4377-4384. doi: 10.1109/JSEN.2020.3035581
[18]	Yang Ming, Wang Ying, Cai Chenguang, et al. Monocular vision-based low-frequency vibration calibration method with correction of the guideway bending in a long-stroke shaker[J]. Optics Express, 2019, 27(11): 15968-15981. doi: 10.1364/OE.27.015968