Analysis of a Structure Design of Skin Friction Sensors Based on FEM

CHEN Jianing; YIN Ruiduo; MA Binghui; XIAO Yao; MU Congcong; XIE Xiaobin

doi:10.12338/j.issn.2096-9015.2021.0141

Volume 65 Issue 11

Nov. 2021

Turn off MathJax

Article Contents

Article Navigation > Metrology Science and Technology > 2021 > 65(11): 45-49, 55

CHEN Jianing, YIN Ruiduo, MA Binghui, XIAO Yao, MU Congcong, XIE Xiaobin. Analysis of a Structure Design of Skin Friction Sensors Based on FEM[J]. Metrology Science and Technology, 2021, 65(11): 45-49, 55. doi: 10.12338/j.issn.2096-9015.2021.0141

Citation:

CHEN Jianing, YIN Ruiduo, MA Binghui, XIAO Yao, MU Congcong, XIE Xiaobin. Analysis of a Structure Design of Skin Friction Sensors Based on FEM[J]. Metrology Science and Technology, 2021, 65(11): 45-49, 55. doi: 10.12338/j.issn.2096-9015.2021.0141

Citation:

PDF( 907 KB)

Analysis of a Structure Design of Skin Friction Sensors Based on FEM

doi: 10.12338/j.issn.2096-9015.2021.0141

1.
Zhejiang Province Institute of Metrology, Hangzhou 310016, China
2.
Zhejiang University, Hangzhou 310027, China

Available Online: 2021-08-18
Publish Date: 2021-11-01

Abstract

Abstract

Skin friction is a major part of the total resistance an object encounters when moving in a fluid. Due to the difficulty in theoretical analysis and the diversity of flow fields, direct measurement of skin friction is needed in various applications. This paper introduces a design of elastic body for strain-type skin friction sensors. A mechanical analysis of the sensor was carried out. The analysis showed that the radius of the sensor’s hole, the spacing between the parallel beams, and the thickness of the connecting beam are the main parameters affect ing the performance. Then representative combinations of the parameters were selected using the orthogonal experimental method. The strain distribution in the patch area was calculated by using FEM. New parameters were defined to coordinate conflicting optimization goals. The influence of each parameter was analyzed to determine an optimal combination.
- skin-friction sensor,
- parallel-beam structure,
- mechanical analysis,
- FEM,
- orthogonal experiment method

FullText(HTML)

References(16)

References

[1]	Preston J H. The Determination of Turbulent Skin Friction by Means of Pitot Tubes[J]. Journal of the Royal Aeronautical Society, 1954, 58(518): 109-121. doi: 10.1017/S0368393100097704
[2]	MacLean M, J A Schetz. Numerical Study of Detailed Flow Affecting a Direct Measuring Skin-Friction Gauge[J]. AIAA Journal, 2003, 41(7): 1271-1281. doi: 10.2514/2.2095
[3]	Blasius H. Grenzschichten in flüssigkeitenmitkleinerreibung[J]. Zeitschrift fur Angewandte Mathematic und Physik, 1908, 56(1): 1-37.
[4]	王雄, 许晓斌, 王南天, 等. 微量摩阻天平旋转加载校准装置研制[J]. 中国测试, 2019, 45(1): 83-87. doi: 10.11857/j.issn.1674-5124.2018100104
[5]	马洪强, 高贺, 毕志献. 超高声速飞行器相关的摩擦阻力直接测量技术[J]. 实验流体力学, 2011, 25(4): 83-88. doi: 10.3969/j.issn.1672-9897.2011.04.016
[6]	Naughton J W, DeMillard E, Davidson P. Skin Friction Measurements to Support Viscous Drag Reduction[C]. 32^ndAIAA Aerodynamic Measurement Technology and Ground Testing Conference, 2016.
[7]	Miozzi M, Felice F D, Klein C, et al. Taylor hypothesis applied to direct measurement of skin friction using data from Temperature Sensitive Paint[J]. Experimental Thermal and Fluid Science, 2019, 110(2020): 109913.
[8]	Smith T B. Development and Ground Testing of Direct Measuring Skin Friction Gages for High Enthalpy Supersonic Flight Tests[D]. Virginia Polytechnic Institute and State University, 2001.
[9]	Silvester T B, Morgan R G. Skin-Friction Measurements and Flow Establishment Within a Long Duct at Superorbital Speeds[J]. AIAA Journal, 2015, 46(2): 527-536.
[10]	吕治国, 李国君, 赵荣娟, 等. 激波风洞高超声速摩阻直接测量技术研究[J]. 实验流体力学, 2013, 27(6): 81-85. doi: 10.3969/j.issn.1672-9897.2013.06.015
[11]	Tiwana M I, Remond S J, Lovell N H. A Review of Tactile Sensing Technologies with Applications in Biomedical Engineering[J]. Sensor and Actuators A: Physical, 2012, 179: 17-31. doi: 10.1016/j.sna.2012.02.051
[12]	Meritt R J, Schetz J A. Skin Friction Sensor Development, Validation, and Application for High-Speed, High-Enthalpy Flow Conditions[J]. Journal of Propulsion and Power, 2016, 32(4): 1-13.
[13]	赵荣娟, 吕治国, 黄军, 等. 基于压电敏感元件的摩阻天平设计[J]. 空气动力学学报, 2018(4): 555-560. doi: 10.7638/kqdlxxb-2016.0112
[14]	Perez E A A L, Pauliac-Vaujour E, Mouis M. Static finite element modeling for sensor design and processing of an individually contacted laterally-bent piezoelectric nanowire[J]. IEEE Transactions on Nanotechnology, 2016, 15(3): 521-526. doi: 10.1109/TNANO.2016.2549064
[15]	Karna S K, Sahai R. An Overview on Taguchi Method[J]. International Journal of Engineering and Mathematical Sciences, 2012(1): 11-18.
[16]	方开泰, 马长兴. 正交与均匀试验设计[M]. 北京: 科学出版社, 2001: 35-43.