Research on the Measurement Method of Voltage Standing Wave Ratio for Signal Source

SU Teng; GUO Min; LIU Guibin; ZHANG Le

doi:10.12338/j.issn.2096-9015.2021.0576

Volume 66 Issue 7

Aug. 2022

Turn off MathJax

Article Contents

Article Navigation > Metrology Science and Technology > 2022 > 66(7): 33-37

SU Teng, GUO Min, LIU Guibin, ZHANG Le. Research on the Measurement Method of Voltage Standing Wave Ratio for Signal Source[J]. Metrology Science and Technology, 2022, 66(7): 33-37. doi: 10.12338/j.issn.2096-9015.2021.0576

Citation:

SU Teng, GUO Min, LIU Guibin, ZHANG Le. Research on the Measurement Method of Voltage Standing Wave Ratio for Signal Source[J]. Metrology Science and Technology, 2022, 66(7): 33-37. doi: 10.12338/j.issn.2096-9015.2021.0576

Citation:

PDF( 958 KB)

Research on the Measurement Method of Voltage Standing Wave Ratio for Signal Source

doi: 10.12338/j.issn.2096-9015.2021.0576

China Jiuquan Satellite Launch Center, Jiuquan 735000, China

Accepted Date: 2022-02-25

Available Online: 2022-03-03

Publish Date: 2022-08-04

Abstract

Abstract

As one of the important performance parameters of the signal source, it is of great significance to measure the signal source voltage standing wave ratio（VSWR）accurately. Based on studying the structure of the signal source and the two working mechanisms of “RF OFF”, the influence of "RF ON" and "RF OFF" on the measurement results of VSWR for the signal source was analyzed. With a vector network analyzer as the measurement equipment, this paper studies the measurement methods of VSWR for signal sources in different modes. The experimental results showed that the passive device measurement method under the condition of “RF OFF” can be used for the signal source with fast closing mode, while the frequency offset measurement method under the condition of “RF ON” can be used for the complete shutdown mode.
- signal source,
- voltage standing wave ratio(VSWR),
- vector network analyzer,
- fast closing mode,
- complete shutdown mode

FullText(HTML)

References(15)

References

[1]	詹志强. 信号发生器的分类、应用领域及发展趋势[J]. 上海计量测试, 2018(4): 2-7. doi: 10.3969/j.issn.1673-2235.2018.04.002
[2]	Zhang Hui, Gao Ling, YanNan Zhai, et al. The Design of Signal Generator based on Virtual Instrument[C]. 3rd International Conference on Machinery, Materials and Information Technology Applications. Qingdao, 2015: 305-308.
[3]	陈娜. 多状态技术在信号源驻波比测量中的应用研究[D]. 西安: 西安电子科技大学, 2013.
[4]	代明珍, 崔孝海, 刘欣萌. WR-28功率基准系统中等效源反射系数校准研究[J]. 计量学报, 2012, 33(1): 68-72. doi: 10.3969/j.issn.1000-1158.2012.01.15
[5]	张翠翠, 王益, 王建忠. 有源器件端口反射系数测量方法分析[J]. 太赫兹科学与电子信息学报, 2015, 13(2): 267-271. doi: 10.11805/TKYDA20150217.267
[6]	方维海, 温鑫, 张璐, 等. 信号源复反射系数测量技术研究[J]. 微波学报, 2014, 30(3): 63-66.
[7]	唐宗熙, 李恩. 一种测量微波功率放大器件输出端反射系数的新方法[J]. 计量学报, 2001, 22(2): 147-151. doi: 10.3321/j.issn:1000-1158.2001.02.014
[8]	王永, 周建烨, 汤瑞. 信号源单音信号功率的精确调节与校准[J]. 电子产品世界, 2020, 27(8): 65-69.
[9]	石博文. 矢量信号源输出电路的研究与实现[D]. 成都: 电子科技大学, 2016.
[10]	Joel P. Dunsmore. 微波器件测量手册—矢量网络分析仪高级测量技术指南[M]. 北京: 电子工业出版社, 2014: 251-252.
[11]	冉志强, 孙景禄, 周峰. 信号发生器信号开时电压驻波比测试方法及自动化研究[J]. 现代测量与实验室管理, 2014, 22(3): 3-5. doi: 10.3969/j.issn.1673-8764.2014.03.001
[12]	曹佳伟. 双端口矢量网络分析仪的中频模块设计[D]. 成都: 电子科技大学, 2019.
[13]	曹悦. 矢量网络分析仪测量不确定度研究与评估[D]. 成都: 电子科技大学, 2020.
[14]	陆福敏, 詹志强, 葛振杰. 一种校准选频电平表不平衡输入电平测量准确度的新方法[J]. 计量技术, 2018(12): 43-46.
[15]	朱长春, 曾亮, 徐伟, 等. 微波及连续频点频率稳定度校准技术研究与运用[J]. 计量技术, 2019(2): 21-24.