Study of a Geometric Parameter Follow-Up Calibration Device

LONG Kuan; QU Jiansu; QIAO Lei; JIA Kailai; SUN Anbin; GAO Ting

doi:10.12338/j.issn.2096-9015.2021.0584

Volume 66 Issue 3

Mar. 2022

Turn off MathJax

Article Contents

Article Navigation > Metrology Science and Technology > 2022 > 66(3): 41-48

LONG Kuan, QU Jiansu, QIAO Lei, JIA Kailai, SUN Anbin, GAO Ting. Study of a Geometric Parameter Follow-Up Calibration Device[J]. Metrology Science and Technology, 2022, 66(3): 41-48. doi: 10.12338/j.issn.2096-9015.2021.0584

Citation:

LONG Kuan, QU Jiansu, QIAO Lei, JIA Kailai, SUN Anbin, GAO Ting. Study of a Geometric Parameter Follow-Up Calibration Device[J]. Metrology Science and Technology, 2022, 66(3): 41-48. doi: 10.12338/j.issn.2096-9015.2021.0584

Citation:

PDF( 1299 KB)

Study of a Geometric Parameter Follow-Up Calibration Device

doi: 10.12338/j.issn.2096-9015.2021.0584

1.
Aecc South Industry Company Limited Co. Ltd., Zhuzhou 412000, China
2.
AVIC Changcheng Institute of Metrology & Measurement, Beijing 100095, China

Available Online: 2022-02-24
Publish Date: 2022-03-08

Abstract

Abstract

To solve the problem of on-site calibration of mechanical accuracy of some non-standard equipment with geometric parameters, a set of follow-up calibration device integrating displacement and angle was designed, and the grating signal acquisition and measurement system design and software development were carried out. Through a large number of field comparative tests under different conditions, technical problems such as rotational eccentricity were solved, and the reliability of the system and the effectiveness of the device were verified. Through the research of geometric parameter follow-up calibration device, the application of follow-up calibration technology in geometric parameter equipment calibration is realized.
- displacement,
- angle,
- follow-up calibration,
- rotation measurement system,
- follow-up grating system

FullText(HTML)

References(15)

References

[1]	阮大文, 茅健, 刘钢, 等. 双五轴数控铣削机床旋转轴误差辨识方法[J]. 中国机械工程, 2020, 31(13): 1548-1554.
[2]	马国艳. 数控机床回转轴应用技术[J]. 世界制造技术与装备市场, 2020(5): 84-85. doi: 10.3969/j.issn.1015-4809.2020.05.027
[3]	苟铖, 彭希锋, 张强. 几何量综合自动检定装置设计[J]. 计量技术, 2018(12): 54-57.
[4]	徐永, 孙安斌, 曹铁泽, 等. RCS测试系统几何量参数综合校准技术研究[J]. 宇航计测技术, 2015, 35(5): 70-74. doi: 10.3969/j.issn.1000-7202.2015.05.019
[5]	厉志飞, 陈刚, 赵建峰, 等. 基于激光位移传感器与标准样板的机器人几何参数标定[J]. 计量技术, 2019(9): 17-21.
[6]	葛敏雪. 高分辨率锥束CT系统几何校准方法研究[D]. 重庆: 重庆大学, 2018.
[7]	张辰, 吴丕杰. 水浸超声C扫描检测系统的机械精度对检测结果的影响[J]. 中国钛业, 2017(1): 36-39.
[8]	董欣媛, 孙双花, 崔京远, 等. 基于正交双轴激光干涉仪的二维光栅校准系统误差分析[J]. 计量学报, 2019, 40(S1): 36-41.
[9]	常莹. RVDT角位移传感器校准技术研究[J]. 宇航计测技术, 2019, 39(S1): 61-66.
[10]	林云川, 程志远. 数控机床在线测量系统校准技术研究[J]. 计测技术, 2020, 40(4): 19-22.
[11]	李新, 茅晨, 马涛, 等. 利用Leica激光跟踪仪对工业机器人现场标定的方法[J]. 计量技术, 2019(11): 64-68.
[12]	焦扬, 黄明, 刘品宽, 等. 双角度编码器超精密转台测角误差校准[J]. 光学精密工程, 2019, 27(10): 2180-2191.
[13]	魏枫, 王欢, 宋薇. 基于二维转台与空间方位角标定装置的电磁轨道发射轴线标定与校准装置设计[J]. 科技创新与应用, 2019(3): 6-10.
[14]	黄建明, 张明达. 角位移传感器自动校准系统[J]. 计量技术, 2017(4): 40-43.
[15]	王民越. 数控机床在线测量系统校准方法的研究[D]. 大连: 大连理工大学, 2018.